Master the 300 115 switch pdf SWITCH Implementing Cisco IP Switched Networks content and be ready for exam day success quickly with this Testking examcollection 300 115 exam topics. We guarantee it!We make it a reality and give you real 300 115 switch pdf questions in our Cisco ccnp switch 300 115 labs braindumps.Latest 100% VALID Cisco 300 115 vce Exam Questions Dumps at below page. You can use our Cisco 300 115 switch pdf braindumps and pass your exam.

P.S. Verified 300-115 questions are available on Google Drive, GET MORE: https://drive.google.com/open?id=1V3EjdNAQ30Y30Ko-7P1GWcqZQ5NzdlhZ


New Cisco 300-115 Exam Dumps Collection (Question 13 - Question 22)

Q1. Refer to the exhibit.

Which option is the most likely explanation of the duplicate address message logged?

A. spanning-tree loop

B. HSRP misconfiguration

C. a PC with IP of 10.10.1.1

D. a hardware problem

Answer: B



Q2. Which two statements about PortFast are true?

A. The port moves immediately to the forwarding state when a device is connected

B. it allows the port to skip the learning state only.

C. It forces the port to skip all spanning-tree states

D. It is most appropriate for ports that provide connectivity to individual workstations or servers

E. The port is error-disabled if it attempts to move into the listening or /earning states.

Answer: A,D



Q3. If a switch stack is configured to use SDM templates, where are the templates stored?

A. all stack members

B. stack master

C. TFTP server

D. flash memory

Answer: B



Q4. Which feature prevents from sending BPDUs on a portfast enabled port?

A. BPDU guard

B. PortFast

C. root guard

D. BPDU filtering

Answer: D



Q5. An access switch at a remote location is connected to the spanning-tree root with redundant uplinks. A network engineer notices that there are issues with the physical cabling of the current root port. The engineer decides to force the secondary link to be the desired forwarding root port.

Which action accomplishes this task?

A. Change the link-type to point-to-point.

B. Enable Rapid Spanning Tree to converge using the secondary link.

C. Adjust the secondary link to have a lower priority than the primary link.

D. Apply a BPDU filter on the primary interface of the remote switches.

Answer: C



Q6. Which component does the GLBP client cache stores for each host of a particular GLBP group?

A. IP address

B. MAC address

C. VLAN

D. Token ring

E. DCSP

Answer: B



Q7. CORRECT TEXTThe headquarter office for a cement manufacturer is installing a temporary Catalyst 3550 in an IDF to connect 24 additional users.

To prevent network corruption, it is important to have the correct configuration prior to connecting to the

production network.

It will be necessary to ensure that the switch does not participate in VTP but forwards VTP advertisements that are received on trunk ports.

Because of errors that have been experienced on office computers, all non-trunking interfaces should transition immediately to the forwarding state of Spanning tree. Also configure the user ports (all FastEthernet ports) so that the ports are permanently non-trunking.

Requirement:

You will configure FastEthernet ports 0/12 through 0/24 for users who belong to VLAN 20. Also all VLAN and VTP configurations are to be completed in global configuration mode as VLAN database mode is being

deprecated by Cisco. You are required to accomplish the following tasks:

1. Ensure the switch does not participate in VTP but forwards VTP advertisements received on trunk ports.

2. Ensure all non-trunking interfaces (Fa0/1 to Fa0/24) transition immediately to the forwarding state of

Spanning-Tree.

3. Ensure all FastEthernet interfaces are in a permanent non-trunking mode.

4. Place FastEthernet interfaces 0/12 through 0/24 in VLAN 20.

Answer:

Please Refer to Explanation below for details:

Explanation/Reference:

Console into the Switch Switch>enable Switch#configure terminal

Switch(config)#interface range fa0/1 u2013 24

Switch(config-if-range)#switchport mode access <<Make all FastEthernet interfaces into access mode.

Switch(config-if-range)#spanning-tree portfast <<Enables the PortFast on interface. Next, we need to assign FastEthernet ports 0/12 through 0/24 to VLAN 20. By default, all ports on the switch

are in VLAN 1. To change the VLAN associated with a port, you need to go to each interface (or a range of

interfaces) and tell it which VLAN to be a part of. Switch(config-if-range)#interface range fa0/12 u2013 24

Switch(config-if-range)#switchport access vlan 20 <<Make these ports members of vlan 20 Switch(config-if-range)#exit

Next we need to make this switch in transparent mode. In this mode, switch doesnu2019t participate in the VTP

domain, but it still forwards VTP advertisements through any configured trunk links. Switch(config)#vtp mode transparent

Switch(config)#exit

Switch#copy running-config startup-config



Q8. Refer to the exhibit.

Currently, R1 is the VRRP master virtual router. Which statement about the VRRP configuration on R1 and R2 is true?

A. Communication between VRRP members is encrypted using MD5.

B. R1 has a route to 10.10.1.1/32 in its routing table.

C. R2 does not have a route to 10.10.1.11/32 in its routing table.

D. R2 becomes master if R1 reboots or track in R1 does not fail.

Answer: B



Q9. Which two statements about CDP are true? (Choose two.)

A. CDP uses a TLV to advertise the native VLAN

B. CDP is not supported with SNMP

C. CDP is supported on Frame Relay sub interfaces.

D. CDP runs on OSI layer 2

E. CDP runs on OSI layer 1

Answer: A,D



Q10. Which file lists all of the configured VLANs on a switch?

A. flash:vlan.dat

B. nvram:vlans.xml

C. flash:vlans.txt

D. nvram:vlan.txt

E. flash.config.txt

F. flash:vlan.xml

Answer: A



Recommend!! Get the Verified 300-115 dumps in VCE and PDF From Examcollectionplus, Welcome to download: https://www.examcollectionplus.net/vce-300-115/ (New 522 Q&As Version)