Exambible 300 075 dump Questions are updated and all 300 075 dump answers are verified by experts. Once you have completely prepared with our 300 075 ciptv2 exam prep kits you will be ready for the real 300 075 vce exam without a problem. We have Most recent Cisco 300 075 dump dumps study guide. PASSED cisco 300 075 First attempt! Here What I Did.
Q73. Which two are gatekeeper-controlled trunk options that support gatekeeper call administration control? (Choose two.)
Q74. If the device pool in the phone record does not match the device pools in the matching subnet, what will the system consider the phone to be?
D. new device
Q75. Which command is needed to utilize local dial peers on an MGCP-controlled ISR during an SRST failover?
A. ccm-manager fallback-mgcp
D. isdn overlap-receiving
Q76. A Cisco Unified Communications Manager cluster is installed in headquarters only.
How can international calls be blocked while national calls are allowed for branch office Cisco IP Phones during a WAN failure?
A. Configure CSS and partitions in Cisco Unified Communications Manager and apply the CSS and partitions to the SRST ISR.
B. Configure CSS and partitions in the SRST ISR.
C. Configure COR in the SRST ISR.
D. Configure voice translations in the SRST ISR.
Q77. Refer to the exhibit.
The HQ site uses area code 650. The BR1 site uses area code 408. The long distance national code for PSTN dialing is 1. To make a long distance national call, an HQ or BR1 user dials access code 9, followed by 1, and then the 10-digit number.
Both sites use MGCP gateways. AAR must use globalized call routing using a single route pattern. Assume that all outgoing PSTN numbers are localized at the egress gateway as shown in the exhibit.
How many route lists and route groups should be configured for AAR at a minimum?
A. a single route list with a local route group for each site
B. two route lists and two route groups for each site
C. a single route list and four route groups for each site
D. None. The AAR CSS can point directly to the route pattern.
Q78. Cisco Unified border element is configured to support RSVP-based CAC. When is the RSVP path and reservation message sent and received?
A. Immediately after the call setup message is received and the reservation message is received after H.245 capabilities negotiation is completed.
B. The path and reservation messages are sent and received after the H.245 capabilities negotiation is completed.
C. The path and reservation messages are sent and received immediately after the call setup message is received.
D. The path is setup once the global command call rsvp-sync is configured.
Q79. Which option indicates the best QoS parameters for interactive video?
A. 1% Max Loss, 150 ms One-way Latency, 30 ms Jitter, 20% Overprovisioning
B. 5% Max Loss, 5 s One-way Latency, 30 ms Jitter, 20% Overprovisioning
C. 0% Max Loss, 100 ms One-way Latency, 30 ms Jitter, 20% Overprovisioning
D. 1% Max Loss, 160 ms One-way Latency, 60 ms Jitter, 10% Overprovisioning
Q80. What is the difference between an MGCP gateway and a SIP gateway?
A. An MGCP gateway that dial peers be configured before PSTN calls can be placed and received. The SIP gateway requires no dial peers.
B. An MGCP gateway can be added in Cisco Unified Communications Manager under the Gateway Type field using the gateway model. The SIP gateway can connect to Cisco Unified Communications Manager only through a SIP trunk.
C. A SIP gateway requires a call agent for PSTN calls to be placed and received. An MGCP gateway does not require a call agent for PSTN calls to be placed and received.
D. An MGCP gateway can register with Cisco Unified Communications Manager. A SIP gateway will show status of "Unknown".
E. The SIP gateway must be configured in Cisco Unified Communications Manager using a valid IP address on the gateway. The MGCP gateway must be configured in Cisco Unified
Communications Manager using the domain name.