We provide real ccna 200 125 study guide exam questions and answers braindumps in two formats. Download PDF & Practice Tests. Pass Cisco 200 125 ccna pdf Exam quickly & easily. The ccna 200 125 pdf PDF type is available for reading and printing. You can print more and practice many times. With the help of our Cisco cisco ccna 200 125 dumps pdf and vce product and material, you can easily pass the ccna 200 125 pdf exam.

P.S. Real 200-125 free demo are available on Google Drive, GET MORE: https://drive.google.com/open?id=1kYtwvDfK3CIMnjUzKdkde8F69Zg0NhM8


New Cisco 200-125 Exam Dumps Collection (Question 7 - Question 16)

Q1. Which two are advantages of static routing when compared to dynamic routing? (Choose two.)

A. Configuration complexity decreases as network size increases.

B. Security increases because only the network administrator may change the routing table.

C. Route summarization is computed automatically by the router.

D. Routing tables adapt automatically to topology changes.

E. An efficient algorithm is used to build routing tables, using automatic updates.

F. Routing updates are automatically sent to neighbors.

G. Routing traffic load is reduced when used in stub network links.

Answer: B,G

Explanation:

Since static routing is a manual process, it can be argued that it is more secure (and more prone to human errors) since the network administrator will need to make changes to the routing table directly. Also, in stub networks where there is only a single uplink connection, the load is reduced as stub routers just need a single static default route, instead of many routes that all have the same next hop IP address.


Q2. Which statement describes VRRP object tracking?

A. It monitors traffic flow and link utilization.

B. It ensures the best VRRP router is the virtual router master for the group.

C. It causes traffic to dynamically move to higher bandwidth links.

D. It thwarts man-in-the-middle attacks.

Answer: B

Explanation:

Object tracking is the process of tracking the state of a configured object and uses that state to determine the priority of the VRRP router in a VRRP group.


Q3. What are three reasons that an organization with multiple branch offices and roaming users might implement a Cisco VPN solution instead of point-to-point WAN links? (Choose three.)

A. reduced cost

B. better throughput

C. broadband incompatibility

D. increased security

E. scalability

F. reduced latency

Answer: A,D,E

Explanation:

IPsec offer a number of advantages over point to point WAN links, particularly when multiple locations are involved. These include reduced cost, increased security since all traffic is encrypted, and increased scalability as s single WAN link can be used to connect to all locations in a VPN, where as a point to point link would need to be provisioned to each location.


Q4. What is the result of issuing the frame-relay map ip 192.168.1.2 202 broadcast command?

A. defines the destination IP address that is used in all broadcast packets on DCLI 202

B. defines the source IP address that is used in all broadcast packets on DCLI 202

C. defines the DLCI on which packets from the 192.168.1.2 IP address are received

D. defines the DLCI that is used for all packets that are sent to the 192.168.1.2 IP address

Answer: D

Explanation:

This command identifies the DLCI that should be used for all packets destined to the 192.168.1.2 address. In this case, DLCI 202 should be used.


Q5. Refer to the exhibit.

How should the FastEthernet0/1 ports on the switches that are shown in the exhibit be configured to allow connectivity between all devices?

A. The ports only need to be connected by a crossover cable.

B. SwitchX(config)# interface fastethernet 0/1 SwitchX(config-if)# switchport mode trunk

C. SwitchX(config)# interface fastethernet 0/1 SwitchX(config-if)# switchport mode access SwitchX(config-if)# switchport access vlan 1

D. SwitchX(config)# interface fastethernet 0/1 SwitchX(config-if)# switchport mode trunk SwitchX(config-if)# switchport trunk vlan 1 SwitchX(config-if)# switchport trunk vlan 10 SwitchX(config-if)# switchport trunk vlan 20

Answer: B

Explanation:

IN order for multiple VLANs to cross switches, the connection between the switches must be a trunk. The u201cswitchport mode trunku201d command is all that is needed, the individual VLANs should not be listed over that trunk interface.


Q6. Based on the network shown in the graphic

Which option contains both the potential networking problem and the protocol or setting that should be used to prevent the problem?

A. routing loops, hold down timers

B. switching loops, split horizon

C. routing loops, split horizon

D. switching loops, VTP

E. routing loops, STP

F. switching loops, STP

Answer: F

Explanation:

The Spanning-Tree Protocol (STP) prevents loops from being formed when switches or bridges are interconnected via multiple paths. Spanning-Tree Protocol implements the 802.1D IEEE algorithm by exchanging BPDU messages with other switches to detect loops, and then removes the loop by shutting down selected bridge interfaces. This algorithm guarantees that there is one and only one active path between two network devices.


Q7. What command is used to verify the DLCI destination address in a Frame Relay static configuration?

A. show frame-relay pvc

B. show frame-relay lmi

C. show frame-relay map

D. show frame relay end-to-end

Answer: C

Explanation:

Sample u201cshow frame-relay mapu201d output: R1#sh frame map

Serial0/0 (up): ip 10.4.4.1dlci 401(0x191,0x6410), dynamic, broadcast,, status defined, active

Serial0/0 (up): ip 10.4.4.3dlci 403(0x193,0x6430), dynamic, broadcast,, status defined, active

Serial0/0 (up): ip 10.4.4.4dlci 401(0x191,0x6410), static, CISCO, status defined, active


Q8. What information does a router running a link-state protocol use to build and maintain its topological database? (Choose two.)

A. hello packets

B. SAP messages sent by other routers

C. LSAs from other routers

D. beacons received on point-to-point links

E. routing tables received from other link-state routers

F. TTL packets from designated routers

Answer: A,C

Explanation:

Neighbor discovery is the first step in getting a link state environment up and running. In keeping with the friendly neighbor terminology, a Hello protocol is used for this step. The protocol will define a Hello packet format and a procedure for exchanging the packets and processing the information the packets contain.

After the adjacencies are established, the routers may begin sending out LSAs. As the term flooding implies, the advertisements are sent to every neighbor. In turn, each received LSA is copied and forwarded to every neighbor except the one that sent the LSA.


Q9. Which IEEE standard protocol is initiated as a result of successful DTP completion in a switch over Fast Ethernet?

A. 802.3ad

B. 802.1w

C. 802.1D

D. 802.1Q

Answer: D

Explanation:

Dynamic Trunking Protocol (DTP) is a Cisco proprietary protocol for negotiating trunking on a link between two devices and for negotiating the type of trunking encapsulation (802.1Q) to be used.


Q10. What OSPF command, when configured, will include all interfaces into area 0?

A. network 0.0.0.0 255.255.255.255 area 0

B. network 0.0.0.0 0.0.0.0 area 0

C. network 255.255.255.255 0.0.0.0 area 0

D. network all-interfaces area 0

Answer: A

Explanation:

Example 3-1 displays OSPF with a process ID of 1 and places all interfaces configured with an IP address in area 0. The network commandnetwork 0.0.0.0 255.255.255.255 area 0 dictates that you do not care (255.255.255.255) what the IP address is, but if an IP address is enabled on any interface, place it in area 0.

Example 3-1Configuring OSPF in a Single Area

router ospf 1

network 0.0.0.0 255.255.255.255 area 0

Reference: http://www.ciscopress.com/articles/article.asp?p=26919&seqNum=3


Recommend!! Get the Real 200-125 dumps in VCE and PDF From 2passeasy, Welcome to download: https://www.2passeasy.com/dumps/200-125/ (New 890 Q&As Version)