Examcollection 201-450 Questions are updated and all 201-450 answers are verified by experts. Once you have completely prepared with our 201-450 exam prep kits you will be ready for the real 201-450 exam without a problem. We have Rebirth LPI 201-450 dumps study guide. PASSED 201-450 First attempt! Here What I Did.
New LPI 201-450 Exam Dumps Collection (Question 3 - Question 12)
Q1. Which of the following configuration files are used by tcpwrapper?
A. /etc/tcpd.allow and etc/tcpd.deny
B. /etc/tcpwrapper.allow and /etc/tcpwrapper.deny
C. /etc/hosts.allow and /etc/hosts.deny
D. /etc/service.allow and /etc/service.deny
Q2. What information is found in the following excerpt from the file /proc/mdstat? (Choose two.)
A. One of the disks in /dev/md0 has failed and a spare disk is used to recreate full redundancy
B. The spare disk /dev/sda1 is used to restore full redundancy after the current recovery
C. The information [UU_] means, that the raid is missing one disk and is not fully redundant
D. The device is using version 1.2 metadata to allow LILO and GRUB Legacy to use /dev/md0 as the boot partition. This would not have been necessary with GRUB2
E. The information [3/2] means that 3 RAID disks belong to the array and 2 disks are spare. Together they equal the number of available disks
Q3. Which of the following filter keywords for tcpdump specify the transfer direction for network packets? (Choose TWO correct answers.)
D. src or dst
Q4. In the output of sar u2013b, what does tps stand for?
A. Terrabyte per second
B. Traffic per second
C. Transfers per second
D. Total data per second
E. Terrabit per second
Q5. Which of the following commands erases the contents of the /dev/sdb3 partition?
A. rm /dev/sdb3
B. dd if=/dev/zero of=/dev/sdb3
C. dd of=/dev/zero if=/dev/sdb3
D. umount /dev/sdb3
Q6. Which of the following commands lists IPv4 addresses and MAC addresses of network nodes that the local system has seen on its directly connected IP networks?
Q7. What command is used to send messages to all users currently logged in? (Specify ONLY the command without any path or parameters.)
Q8. What should be done to ensure a client machine uses the recursive nameserver running on the IP address 192.168.1.1 ? (Choose TWO correct answers.)
A. Add nameserver 192.168.0.1 to /etc/resolv.conf.
B. Run route add nameserver 192.168.0.1.
C. Run ifconfig eth0 nameserver 192.168.0.1.
D. Ensure that the dns service is listed in the hosts entry in the /etc/nsswitch.conf file.
E. Run bind add nameserver 192.168.0.1.
Q9. Which RAID level value must be used with Linux software RAID in order to create an array of mirrored devices?
Q10. According to the tcpdump output below, what is the IP address of the client host?
02:12:40.511381 IP 192.168.246.11.1045 > 192.168.246.1.22: S 3838532429:3838532429(0) win 5840 <mss
1460,sackOK,timestamp 31325740,nop,wscale 2>
02:12:40.511540 IP 192.168.246.1.22 > 192.168.246.11.1045: S 1209330085:1209330085(0) ack 383853
2430 win 5792 <mss 1460,sackOK,timestamp 11553457 3132574,nop,wscale 0>
02:12:40.511755 IP 192.168.246.11.1045 > 192.168.246.1.22: . ack 1 win 1460 <nop,nop,timestamp 3 132574
02:12:40.515122 IP 192.168.246.1.22 > 192.168.246.11.1045: P 1:26(25) ack 1 win 5792 <nop,nop,timestamp
02:12:40.515511 IP 192.168.246.11.1045 > 192.168.246.1.22: . ack 26 win 1460 <nop,nop,timestamp
02:12:40.515952 IP 192.168.246.11.1045 > 192.168.246.1.22: P 1:23(22) ack 26 win 1460
<nop,nop,timestamp 3132578 11553460>
100% Rebirth LPI 201-450 Questions & Answers shared by Dumpscollection, Get HERE: http://www.dumpscollection.net/dumps/201-450/ (New Q&As)